How To Put On A Car Cover Easily

It is a common misconception that car cover installation is a lot of work. However, in reality, once you grasp the procedure, it becomes a straightforward process. The steps involve ensuring the correct orientation, aligning everything properly, and securing one end before pulling it over the top. Continue reading for a detailed explanation.

Preparing Your Car

Your car should be completely prepared before applying the car cover. This begins with parking in a suitable location that provides ample space for unpacking and covering. It's also advisable for the car to be clean before car cover installation, especially if it will be covered for an extended period. Additionally, it's crucial for the car to be dry before the cover is applied. Therefore, wipe it down with a towel and let it air dry if needed.

• Inspect the car’s surfaces for debris: Things like small stones and twigs could cause scratches when you apply the cover, so remove them first.
• Fold in mirrors and antenna: If you have foldable wing mirrors or an extendable antenna, fold them in to prevent them from being damaged or from damaging the cover.
• Ensure the windows and sunroof are closed: All windows, including the sunroof, must be closed to prevent moisture or dust from getting into the covered car.
• Consider removing external accessories: Things like bike racks and spoilers may interfere with the correct fit of the cover, so consider removing them.

Following these steps is how to pout on a car cover to avoid problems down the line. And it is essential to have the right type of car cover, so check different sizes and custom fits in our catalog to find which will work best for you.

Steps To Install The Car Cover

Once you have prepared your car, it's time to proceed with the car cover installation. The steps in this section will guide you on how to execute it correctly, ensuring your car receives maximum protection from external elements and potential threats. Follow each step carefully.

1. Start by carefully removing the car cover from its packaging or container.
2. Find the tag on the inside of the car cover that indicates the front. This may be sewn on or stamped, but it is essential to differentiate between the front and rear of the car cover.
3. Align the cover with the car, then secure the front section under the front bumper. This will enable you to pull the cover over the car around to the back.
4. If you ordered one of our custom car covers, it may have pockets for the wing mirrors. Be sure to insert the mirrors into these first before attaching the ends of the cover to the bumpers.
5. If you chose your car cover carefully, you will have taken your car’s antenna into consideration. For antennas that are not retractable, it is wise to add an antenna patch to the inside of the car cover for added protection. A custom car cover may already have provisions included for the antenna, but make sure you are doing what you can to protect the antenna.
6. Finally, ensure the car cover is completely spread over the vehicle, leaving no creases and no part of the car exposed. Pull it in phases to ensure correct alignment and an even spread.

Once the car cover is fully applied, you are ready to secure it in place. This will ensure maximum protection for the car. We provide many accessories for securing your cover in place, and there are usually straps built into the car covers themselves for installation.

How To Strap A Car Cover

Our car covers come with securing straps and buckles. You will discover a pair at the front and another pair at the back, allowing you to fasten the car cover beneath the front and rear bumpers. Just take the straps, walk around the front and rear of the vehicle, then loop the straps under the bumpers and fasten them into the buckles. Pull the straps taut for a snug and secure fit.

You can also order some additional accessories to further secure the fit. These include:

• Cable locks
• Gust guards
• Anchor weights
• Suction cups
• Additional tie-down straps
• Bungee cords

This is how to put on a car cover to achieve a snug fit and protect it from gusts of wind or potential tampering. Your car cover is engineered to maintain your vehicle in prime condition, thus it's imperative to guarantee its proper installation.

You won't achieve successful car cover installation unless you've acquired the correct cover. You require an appropriately sized option, preferably custom-fit for your vehicle, and crafted from the suitable material to provide the necessary protection. We offer an extensive selection of car covers, available in various sizes, fits, and materials within our catalog, ensuring you'll discover the most suitable choice.

It is also crucial to ensure the vehicle is clean and dry, and that loose items are secured. If the cover lacks a soft inner lining, contemplate placing a soft cloth or towel underneath it. Additionally, always apply the cover during moderate weather conditions.

Here are some common car cover installation mistakes to avoid:

• Installing on a hot car: Doing this can cause heat to be trapped underneath the cover, which may damage paint or melt adhesive elements.
• Dragging the cover: If you pull or drag the cover across the car’s surfaces, it can introduce dirt and debris that may scratch the paint.
• Neglecting sharp edges: Failure to account for sharp edges can result in tears to the cover.
• Not inspecting the cover first: Look out for tears or holes in the cover as these could compromise its ability to offer adequate protection.
• Not checking the cover regularly: Once installed, the car cover should be checked daily as it can shift due to wind and weather conditions.

The question of how to put on a car cover involves being attentive to the actions you should and shouldn't take. Keep these considerations in mind whenever you apply your car cover to ensure optimal protection for your vehicle. Both our generic and custom car covers come with detailed instructions to ensure a proper fit based on your car's type or size. Pay heed to these instructions and follow the guidance in this post for a consistent and appropriate fit every time.

It's crucial for a car cover to fit snugly, but it shouldn't be excessively tight. The objective is to attain a secure fit that shields against external elements and avoids flapping in the wind. Nonetheless, it's also advantageous to allow for some airflow beneath the cover. Obtaining the correct car cover size is pivotal, and certain materials offer greater breathability than others.

Here are some car cover installation suggestions to get the right fit:

• The car cover should fit the contours of your vehicle with no excessive slack or extra material that could flap in the wind.
• You must avoid stretching the car cover to make it fit, as this can strain the material. 
• The entirety of the vehicle should be covered from front bumper to rear bumper and both sides.
• The car cover should have sufficient depth to reach the bottom of your car, covering the wheels and preventing wind from getting underneath.
• It shouldn’t be difficult to get the car cover in position, and you should always attach it properly using the built-in straps and any additional accessories you may have.

Remember, how to put on a car cover correctly can vary somewhat between different designs. Custom covers, for instance, are designed to be more form-fitting, while others provide a more relaxed fit. Always refer to the manufacturer's instructions and any included photographs or diagrams as a guide.

The procedure of removing a car cover is equally significant as its proper application. The objective is to remove it in a manner that prevents any damage to both the car cover and the vehicle. Here is the method:

1. Inspect the cover to ensure it is free from debris or dirt.
2. Undo the straps and any additional accessories you have.
3. Fold the cover in sections, either from the front or the back, to remove it in stages.
4. Do the same for the sides, folding inwards towards the center of the car.
5. Lift the bundle from the car and place on a clean, dry section of the ground to fold properly.
6. Once the cover is removed, inspect the vehicle for signs of debris or moisture that may have accumulated during the removal process.

Again, the aim of removing a car cover is to lift it off the vehicle without causing damage and to prepare it for folding and storage. If the car cover is wet, you'll need to hang it up to air dry before folding and storing.

We have a comprehensive article explaining how to fold a car cover. This article covers various considerations and methods, so please refer to it for complete instructions on mastering this process. Correctly folding a car cover is vital for proper storage, ensuring the cover's safety, and extending its lifespan.

Here is the basic process:

• Fold it in a clean and open area.
• Ensure it is dry and shake off debris.
• Fold in half lengthwise, then fold in half again, ensuring all wrinkles are smoothed out.
• Keep folding or rolling tighter.
• Place it in a storage bag - we supply these with orders to provide maximum protection for your car cover.

Removing and folding are important considerations for the car cover installation process, so pay heed to them if you want your cover to have maximum longevity.

As a car owner, it is your responsibility to protect your car to ensure it maintains its appearance and remains undamaged. This practice will allow you to maximize its lifespan and keep it in top condition for an extended period.

Here are key reasons why car cover installation is important:

• They protect your car against the elements.
• They help prevent scratches and dings.
• You get effective UV ray protection.
• Your car will be more resistant to corrosion.
• Threats like tree sap and bird droppings will not be able to touch your car.
• They reduce the need for regular cleaning.

When you possess a car cover, you possess a proactive method for safeguarding your investment. Sustaining your car's aesthetic appeal and functional state are excellent strategies for prolonging its lifespan.

We sell a wide range of car covers, including many different sizes, materials and fits. Here are some tips for buying the appropriate cover for you:

• Know the make, model and year of your car.
• Choose between a custom or universal fit.
• Think about the material - consider indoor vs outdoor use, your local climate and breathability.
• Ensure you have the appropriate securing mechanisms - additional ones are available if you want a little extra.
• Stay within your budget.

The correct fit and material are important considerations for how to put on a car cover. Get these choices right from the outset.